Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1
  • 2

TOPIC: Just finished build of my PedalShield DUE

Just finished build of my PedalShield DUE 2 years 7 months ago #761

  • gmarti
  • gmarti's Avatar
  • OFFLINE
  • Junior Member
  • Posts: 25
  • Thank you received: 10
  • Karma: 4
Hello everyone,

After 2 weeks looking for time, I have finally finished mounting my pedalShield. :pedalboss:

I leave here some photos. Now let's go through the programming phase and look for some kind of enclosure to make it look nicer. :P


2017-03-2419.26.23.jpg



2017-03-2419.54.51.jpg
The administrator has disabled public write access.
The following user(s) said Thank You: Ray

Just finished build of my PedalShield DUE 2 years 7 months ago #767

  • Ray
  • Ray's Avatar
  • OFFLINE
  • Moderator
  • Posts: 695
  • Thank you received: 146
  • Karma: 41
Fantastic photos, good job! ;)
If you find any cool DIY case post it here!
Last Edit: 2 years 7 months ago by Ray.
The administrator has disabled public write access.
The following user(s) said Thank You: gmarti

Just finished build of my PedalShield DUE 2 years 7 months ago #769

  • gmarti
  • gmarti's Avatar
  • OFFLINE
  • Junior Member
  • Posts: 25
  • Thank you received: 10
  • Karma: 4
Well @Ray,

The truth is that I finally dared to make my first 3D design and I already have it done and pending 3D printing in ABS. I hope I have taken the measures well, and it will serve me as an experience.

I leave here the link in case you want to see it. It is very simple and austere, although I hope it will do its job well.

https://www.thingiverse.com/thing:2203506

Captura.png
The administrator has disabled public write access.
The following user(s) said Thank You: Ray

Just finished build of my PedalShield DUE 2 years 7 months ago #775

  • Ray
  • Ray's Avatar
  • OFFLINE
  • Moderator
  • Posts: 695
  • Thank you received: 146
  • Karma: 41
Thanks for your contribution!!!
The administrator has disabled public write access.
The following user(s) said Thank You: gmarti

Just finished build of my PedalShield DUE 2 years 7 months ago #778

  • gmarti
  • gmarti's Avatar
  • OFFLINE
  • Junior Member
  • Posts: 25
  • Thank you received: 10
  • Karma: 4
Good morning.

I have my first 3D impression here for the enclosure.

I have to file some dots to gain 2mm for the USB connector, I tweak a bit for the top cap of the methacrylate cap, but I think I've tuned it pretty well. I leave you some photos. ;)




2017-03-2912.07.15.jpg


2017-03-2912.07.31.jpg
Last Edit: 2 years 7 months ago by gmarti.
The administrator has disabled public write access.

Just finished build of my PedalShield DUE 2 years 7 months ago #779

  • gmarti
  • gmarti's Avatar
  • OFFLINE
  • Junior Member
  • Posts: 25
  • Thank you received: 10
  • Karma: 4
Almost finished, in the absence of small details. :)


2017-03-2917.28.40.jpg


2017-03-2917.28.59.jpg


2017-03-2917.29.33.jpg
The administrator has disabled public write access.

Just finished build of my PedalShield DUE 2 years 7 months ago #780

  • Ray
  • Ray's Avatar
  • OFFLINE
  • Moderator
  • Posts: 695
  • Thank you received: 146
  • Karma: 41
WOW thats an amazing enclosure! I love the way the blue led shines along the border.
Congrats and keep up the good job
Last Edit: 2 years 7 months ago by Ray.
The administrator has disabled public write access.
The following user(s) said Thank You: gmarti

Just finished build of my PedalShield DUE 2 years 7 months ago #783

  • gmarti
  • gmarti's Avatar
  • OFFLINE
  • Junior Member
  • Posts: 25
  • Thank you received: 10
  • Karma: 4
Thank you very much. But, well, I had to do some touch-ups by hand with the help of my Dremmel. ;)

To be able to enter properly the slanted plate touched a bit so I have lowered a millimeter an inner part of the box.

I also lowered the opening where the USB port is connected for programming because the connector did not fit well when touching down.

The connection hole of the output jack also had to be retouched. I did not notice that this connector is a millimeter displaced compared to the input.

And finally I made a hole to access the trimmer VR1 because I also did not take into account in the original design.

So I've updated my design on Tinkercad and Thingverse in case it is useful to someone.

https://www.tinkercad.com/things/cUx6sfmqBcI-pedalshield-case-11

http://www.thingiverse.com/thing:2219858


2017-04-0113.02.24.jpg



2017-04-0113.02.39.jpg



pedalshield11.1.png


pedalshield11.2.png


pedalshield11.3.png
The administrator has disabled public write access.
The following user(s) said Thank You: Ray, BowDown

Just finished build of my PedalShield DUE 2 years 7 months ago #789

  • Ray
  • Ray's Avatar
  • OFFLINE
  • Moderator
  • Posts: 695
  • Thank you received: 146
  • Karma: 41
I love the way the blue led illuminates the top plate with your design, neat job!
The administrator has disabled public write access.

Just finished build of my PedalShield DUE 2 years 7 months ago #792

  • gmarti
  • gmarti's Avatar
  • OFFLINE
  • Junior Member
  • Posts: 25
  • Thank you received: 10
  • Karma: 4
Thank you. :lol:

I am delighted to contribute to this project. ;)
The administrator has disabled public write access.
The following user(s) said Thank You: Ray
  • Page:
  • 1
  • 2
Time to create page: 0.307 seconds
Powered by Kunena Forum
Joomla SEF URLs by Artio