- Mensajes: 702
- Gracias recibidas: 152
How to Build pedalSHIELD MEGA in 5 Steps
- Ray
-
Autor del tema
- Fuera de línea
- Moderador
-
Menos
Más
6 años 3 meses antes - 5 años 4 meses antes #1230
por Ray
How to Build pedalSHIELD MEGA in 5 Steps Publicado por Ray
This PDF explains how to assemble the pedalsHIELD MEGA board step by step with photographs and additional information:
Última Edición: 5 años 4 meses antes por Ray.
El siguiente usuario dijo gracias: Perez
Por favor, Identificarse para unirse a la conversación.
- greenmojo
- Fuera de línea
- Navegador Iniciado
-
Menos
Más
- Mensajes: 5
- Gracias recibidas: 1
5 años 8 meses antes #1497
por greenmojo
Respuesta de greenmojo sobre el tema How to Build pedalSHIELD MEGA in 5 Steps
Hello
Are used by polar electrolytic caps and stead of the recommended caps and wondering if that would make a difference or would cause more distortion not be affected stores in but just distorted audio I have the right caps but I didn’t at the time any info is appreciated thanks
Are used by polar electrolytic caps and stead of the recommended caps and wondering if that would make a difference or would cause more distortion not be affected stores in but just distorted audio I have the right caps but I didn’t at the time any info is appreciated thanks
Por favor, Identificarse para unirse a la conversación.
- greenmojo
- Fuera de línea
- Navegador Iniciado
-
Menos
Más
- Mensajes: 5
- Gracias recibidas: 1
5 años 8 meses antes #1498
por greenmojo
Respuesta de greenmojo sobre el tema How to Build pedalSHIELD MEGA in 5 Steps
hello again...text to speech did do very well. So I used nichicon bi polar electrolytic caps that are 4.7 35v instead of the recommmended. Is this going to cause problems or excessive noise? It is working but there seems to be issues with the effects and them being distorted.
Any info is appreciated.
Thanks
jeff
Any info is appreciated.
Thanks
jeff
Por favor, Identificarse para unirse a la conversación.
- Ray
-
Autor del tema
- Fuera de línea
- Moderador
-
Menos
Más
- Mensajes: 702
- Gracias recibidas: 152
5 años 8 meses antes #1502
por Ray
Respuesta de Ray sobre el tema How to Build pedalSHIELD MEGA in 5 Steps
yes you can use different type of caps as far as they are the same value and they have a similar voltage rating (16V or higher is good). I don't think the distortion would be affected by this change.Are used by polar electrolytic caps and stead of the recommended caps and wondering if that would make a difference or would cause more distortion not be affected stores in but just distorted audio I have the right caps but I didn’t at the time any info is appreciated than
Nichicon bi polar caps are excellent caps (are these the green ones?). They won't produce any additional noise at all. You can replace C3, C6, and C10 this these without problems.So I used nichicon bi polar electrolytic caps that are 4.7 35v instead of the recommmended. Is this going to cause problems or excessive noise? It is working but there seems to be issues with the effects and them being distorted.
Any info is appreciated.
Por favor, Identificarse para unirse a la conversación.
- nfort
- Fuera de línea
- Navegador Iniciado
-
Menos
Más
- Mensajes: 2
- Gracias recibidas: 0
4 años 6 meses antes #2012
por nfort
Respuesta de nfort sobre el tema How to Build pedalSHIELD MEGA in 5 Steps
Hello everyone.
I'm from Argentina, and there no way I can get the oficial PCB, and then start with the 5 steps guide.
Im new with electronics, so I may need some advice for making my own PCB at home.
I have donwloaded the images in order to print it, and then make the PCB. But my very fist question is: what kind of PCB should I buy? I've seen there are multiple kind of pcb: for example sigle layer, o double layer.
If someone could help me with this, it would be awesome, because it's the step 0 in order to get the pedalShield Mega done at home.
I'm from Argentina, and there no way I can get the oficial PCB, and then start with the 5 steps guide.
Im new with electronics, so I may need some advice for making my own PCB at home.
I have donwloaded the images in order to print it, and then make the PCB. But my very fist question is: what kind of PCB should I buy? I've seen there are multiple kind of pcb: for example sigle layer, o double layer.
If someone could help me with this, it would be awesome, because it's the step 0 in order to get the pedalShield Mega done at home.
Por favor, Identificarse para unirse a la conversación.
Tiempo de carga de la página: 0.063 segundos